Expert HVAC solutions for homes and businesses across Lebanon, CT. Certified technicians, transparent pricing, and results you can count on.
Professional HVAC solutions for residential and commercial properties in your community.
Ductwork problems manifest as uneven room temperatures, excessive dust near registers, and HVAC systems that run continuously without satisfying the thermostat. Technicians identify crushed flex runs, separated joints, and deteriorated mastic seals using pressure testing and visual inspection protocols.
Comprehensive HVAC inspections cover thermostat operation, ductwork condition, refrigerant levels, electrical connections, and combustion safety. This detailed assessment identifies efficiency losses, safety hazards, and components nearing end of service life before they result in costly emergency repairs.
When your AC blows warm air, short cycles, or fails to start, the problem may involve a failed compressor, low refrigerant charge, frozen evaporator coil, or faulty control board. Professional repair identifies the exact fault and restores rated SEER efficiency through precise, manufacturer-guided procedures.
Selecting the right heat pump means matching BTU capacity to your structure while accounting for climate zone, insulation levels, and existing ductwork. Professional installation ensures proper refrigerant charge, correct defrost timing, and verified auxiliary heat staging for demanding winter conditions.
Full HVAC installation requires coordination of heating equipment, cooling components, ductwork design, and control systems to deliver efficient comfort at rated capacity. Our technicians perform Manual J and Manual D calculations, size equipment to match your structure, and commission the system to manufacturer standards.
An annual air conditioning tune-up catches refrigerant leaks, worn contactor points, and degraded fan motors before they cascade into compressor damage. Technicians measure temperature differential across the coil, verify amp draws, and confirm proper subcooling to protect your investment.
When your boiler produces inconsistent heat, unusual noises, or pressure fluctuations, the root cause often involves sediment buildup, failing motorized valves, or degraded seals within the hydronic loop. Experienced technicians restore system balance and verify safe operation through combustion analysis.
A professionally installed mini-split eliminates the energy losses associated with traditional ductwork while providing independent temperature control per zone. Technicians mount indoor heads at optimal height, route linesets with proper insulation, and commission each zone for verified heating and cooling output.
Scheduling professional furnace maintenance each fall ensures your heating system delivers full BTU output without wasting fuel. Technicians inspect the inducer motor, verify pressure switch operation, calibrate gas valve output, and clean the burner assembly for reliable cold-weather performance.
Restoring heat pump performance starts with accurate diagnostics of compressor function, reversing valve operation, and refrigerant charge levels. Our NATE-certified technicians service all major brands including Carrier, Trane, Lennox, and Rheem to resolve airflow loss, short cycling, and defrost failures.
When a mini-split displays error codes, produces weak airflow, or fails to reach setpoint, the fault often lies within the inverter board, thermistor sensors, or refrigerant circuit. Professional repair restores rated SEER output and eliminates the inefficient short cycling that drives up utility costs.
Over time, air ducts accumulate dust, pet dander, mold spores, and construction debris that degrade indoor air quality and restrict airflow. Professional duct cleaning uses negative-pressure HEPA-filtered vacuums and rotary brush systems to remove contaminants from supply and return plenums.
Upgrading to a smart thermostat enables precise scheduling, remote access, and energy usage reporting that can reduce heating and cooling costs by 10 to 15 percent. Professional installation ensures correct wiring to your HVAC system, including C-wire verification and multi-stage equipment compatibility.
Sudden HVAC failures often stem from compressor lockout, blown transformer fuses, failed gas valves, or tripped high-pressure switches. Emergency repair service provides same-day response with technicians equipped to diagnose and resolve critical faults across all major heating and cooling equipment brands.
Clogged dryer vents are a leading cause of residential fires, with lint buildup restricting exhaust airflow and causing the dryer to overheat. Professional cleaning removes compacted lint from the full vent run, verifies proper airflow velocity, and inspects the exterior termination for damage.
Since 2013, KIC Refrigeration has delivered expert HVAC service to the close-knit city of Lebanon, CT. Every technician holds NATE certification and arrives with diagnostic tools that pinpoint problems fast. In a smaller community where reputation is everything, ours is built on honest assessments, premium equipment, and systems that perform reliably through every Connecticut season.
From heat pump repairs to complete system installations, our Lebanon crews treat every home and business like it belongs to family. We partner with manufacturers like Carrier, Lennox, and Daikin to offer equipment rated at 16 SEER2 or higher, and we back every job with a workmanship warranty. That commitment to quality is why Lebanon property owners trust KIC Refrigeration with their comfort.
The certifications, standards, and commitments that set our HVAC service apart.
Every technician on our team holds current NATE certification — the highest standard in the HVAC industry for installation and service competency. You get a technician who has passed rigorous exams on system diagnostics, refrigerant handling, and equipment commissioning.
Most service calls are completed the same day you call. Our trucks are stocked with over 200 common parts — capacitors, contactors, ignitors, flame sensors, motors, and control boards — so we resolve the majority of repairs in a single visit without waiting on parts.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
Every technician carries EPA Section 608 Universal certification for refrigerant handling — required by federal law for working with R-410A, R-22, R-32, and all regulated refrigerants. Your system is serviced by technicians who handle refrigerants legally and responsibly.
We carry full general liability and workers compensation coverage on every job. Our HVAC license is current in every state we operate, and we pull permits when local codes require them. Your property and our crew are fully protected on every visit.
Get the information you need to make confident HVAC decisions for your property.
Heat pumps offer both heating and cooling from a single outdoor unit, making them significantly more energy-efficient than furnaces for moderate climates. A heat pump does not generate heat — it transfers it from outdoor air, which requires far less energy than burning gas or running electric resistance coils. Modern cold-climate heat pumps with variable-speed inverter compressors operate effectively down to minus 15 degrees Fahrenheit, making them viable in most Connecticut locations. For Lebanon homeowners with natural gas access, a dual-fuel system — heat pump for primary heating paired with a gas furnace for backup during extreme cold — often provides the best balance of efficiency and performance. Heat pumps also qualify for federal tax credits under the Inflation Reduction Act. KIC Refrigeration evaluates your specific climate zone, insulation levels, and utility rates to determine whether a heat pump, furnace, or dual-fuel system is the smartest investment.
The National Air Duct Cleaners Association recommends professional duct cleaning every 3 to 5 years for most Lebanon homes. However, several factors can shorten that interval: households with pets that shed, family members with allergies or asthma, smokers in the home, and properties that have undergone recent renovation or construction work should consider cleaning every 2 to 3 years. Warning signs that your ducts need attention include visible dust or debris accumulating at register openings, musty or stale odors when the system runs, unexplained respiratory symptoms, and inconsistent airflow between rooms. Our NADCA-compliant cleaning process uses truck-mounted vacuum equipment and rotary brush agitation to remove dust, allergens, mold spores, and debris from your entire duct system. We also inspect for disconnected joints, damaged insulation, and air leaks that reduce system efficiency.
HVAC repair costs in Lebanon typically range from $150 to $500 for minor fixes such as capacitor replacement, contactor swaps, or thermostat wiring issues. Mid-range repairs like blower motor replacement or refrigerant recharging run $500 to $1,200. Major repairs — including compressor replacement, heat exchanger repair, or evaporator coil swap — cost $1,200 to $2,500 or more depending on equipment brand and system type. The final price depends on whether you have a furnace, heat pump, air conditioner, boiler, or ductless mini split, as parts and labor vary significantly between system types. Our NATE-certified technicians diagnose the issue accurately on the first visit, and KIC Refrigeration provides a written estimate with transparent pricing before any work begins. We never charge a diagnostic fee when you proceed with the recommended repair.
We recommend professional HVAC maintenance at least twice per year for Lebanon homeowners — once in spring to prepare your cooling system and once in fall to prepare your heating system. Each tune-up includes a comprehensive multi-point inspection covering filter replacement, refrigerant level verification, electrical connection tightening, thermostat calibration, condensate drain clearing, and performance testing. For the heating check, technicians also inspect the heat exchanger for cracks, test safety switches, and verify gas pressure on furnaces and boilers. Routine maintenance catches small problems — like a failing capacitor or a dirty flame sensor — before they cause complete system failures. Industry data shows that well-maintained HVAC systems last 15 to 20 years compared to 10 to 12 years for neglected equipment, and they operate 15 to 25 percent more efficiently throughout their lifespan.
The ideal time for HVAC replacement in Lebanon is during the shoulder seasons — spring and fall — when demand is lower, equipment availability is highest, and scheduling is more flexible. Contractors are less booked during these periods, which means faster installation timelines and potentially more competitive pricing. You are also more likely to find manufacturer rebates, utility incentive programs, and promotional financing during off-peak months. From a technical standpoint, moderate temperatures allow your new system to be commissioned and tested under less extreme conditions. However, KIC Refrigeration completes HVAC installations year-round in Connecticut and can often start within days of your approved estimate, even during peak summer or winter demand. If your current system is showing signs of failure, do not wait for the perfect season — a planned replacement is always better than an emergency one.
Most residential HVAC installations in Lebanon, CT are completed in 1 to 3 days depending on the system type, condition of existing ductwork, and complexity of the project. A straightforward furnace and air conditioner replacement on existing ductwork typically takes a single day — our crews arrive in the morning and commission the new system by afternoon. Heat pump conversions, ductless multi-zone installations with line sets routed through walls, and projects requiring new or modified ductwork may take 2 to 3 days. Commercial installations and whole-building systems can extend to a week. We schedule around your availability, coordinate all permits and inspections, and protect your flooring and walls throughout the process. Every installation concludes with a full system commissioning including airflow verification and refrigerant charge confirmation.
Thousands of satisfied customers — here is what a few of them had to say.
"Our mini split stopped cooling mid-summer and they fit us in the next morning. Diagnosed a bad capacitor, replaced it on the spot. Back to normal in under an hour."
"KIC Refrigeration did a full HVAC inspection before we closed on our new house. Very detailed report and the inspector answered all my questions patiently."
"Mini split installation went smoothly. Clean work, no mess left behind. Would have liked a bit more explanation on the maintenance schedule but overall very happy."
We also serve these nearby communities with the same certified HVAC expertise.